Controller LK-G5001

LK-G5001 - Controller

*Please note that accessories depicted in the image are for illustrative purposes only and may not be included with the product.

Specifications

Model		LK-G5001
Type		Separate type Main controller
Sensor head compatibility		Compatible
No. of connectable sensor heads		2
Display	Minimum display unit	0.001 µm
	Display range	±999.999 µm to ±9999.99 mm (7 settings selectable)
	Display cycle	Approx 10 times/sec.
Display interface	Display port	Either the display unit (LK-HD500) or dedicated touch panel (LK-HD1001) can be connected
	LED indicator	LASER ON
Terminal block	Analogue output voltage	±10 V output, Output impedance: 100 Ω^*1
	Analogue current output	4 to 20 mA, Maximum load resistance: 350 Ω^*1
	No. of analogue outputs	2^*1
	TIMING 1 input	Non-voltage input^*2
	RESET 1 input
	Auto-zero 1 input
	Laser remote input	Non-voltage input^*1
	Alarm output	NPN open-collector output^*1
	General comparator output
Expansion connector	TIMING input	Non-voltage input^*1
	RESET input
	Auto-zero input
	Program switching input
	Binary selection input
	Alarm output	NPN open-collector output^*1
	Comparator output
	Binary output
RS-232C interface		Baud rate: 9600 to 115200 bps Data length: 8 bits Stop bit length: 1 bit Parity: None/even/odd
USB interface		USB 2.0 Hi-Speed compliant^*3
Ethernet interface		100Base-TX/10Base-T^*4
EtherNet/IP™interface		Cyclic communication (implicit messaging) Message communication (explicit messaging) : UCMM and Class3 Number of connections: 32 Complies with conformance test version CT14^*5
PLC-Link		The following PLCs are supported:Mitsubishi Electric: MELSEC iQ-R Series, iQ-F Series, Q Series, L Series, FX Series EtherNet/IP™, CC-Link, and DeviceNet® cannot be used in conjunction with PLC-Link
Head expansion unit connector		Up to 10 head expansion units can be connected to one main controller
Expansion unit connector		Either of the CC-Link unit (LK-CC100) or DeviceNet® unit (LK-DN100) can be connected
Power supply	Power supply voltage	24 VDC ±10%
	Maximum current consumption	0.6 A or less with 1 head/3.5 A or less with 12 heads
Environmental resistance	Ambient temperature	When one or less head expansion unit is connected: 0 to +50 °C. When two or more head expansion units are connected: 0 to +40 °C.
	Relative humidity	35 to 85 % RH (No condensation)
Weight		Approx. 600 g
^1 NPN open-collector output rating: 50 mA max. (40 V max.), Residual voltage: 0.5 V max. PNP open-collector output rating: 50 mA max. (30 V max.), Residual voltage: 0.5 V max. Non-voltage input rating: ON voltage: 1 V max., OFF current: 0.6 mA max. Voltage input rating: Maximum input rating: 26.4 V, ON voltage: 10.2 V, OFF current: 0.6 mA Part of the input/output circuit of the LK-G5000 Series is internally common. Be careful that no potential difference is generated between the internally common terminals due to the potential difference between the cables/external devices. For details, refer to "Precautions on wiring" in the User's Manual. ^2 NPN open-collector output rating: 50 mA max. (40 V max.), Residual voltage: 0.5 V max. PNP open-collector output rating: 50 mA max. (30 V max.), Residual voltage: 0.5 V max. Non-voltage input rating: ON voltage: 1 V max., OFF current: 0.6 mA max. Voltage input rating: Maximum input rating: 26.4 V, ON voltage: 10.2 V, OFF current: 0.6 mA Part of the input/output circuit of the LK-G5000 Series is internally common. Be careful that no potential difference is generated between the internally common terminals due to the potential difference between the cables/external devices. For details, refer to "Precautions on wiring" in the User's Manual. This input is applied to all of the synchronised OUT. ^3 When a PC supporting USB 1.1 or USB 2.0 full speed is connected, the data refresh cycle and other operations may slow down. ^4 Use the Ethernet interface only for direct connections with a PC or for local network connections with a PC or LK-G5000 Series units. ^*5 The EtherNet/IP™ interface cannot be used when a CC-Link unit or a DeviceNet® unit is installed. EtherNet/IP™ is supported by the latest controllers. For details on which controllers support EtherNet/IP™ , contact your nearest KEYENCE office.

Data Sheet (PDF) Other Models